Atexxo Manufacturing

Specialist in Atex and IECEx Solutions

info@atexxo.com
+31(0)186 601 299
    
  • Atexxo Manufacturing
    • Contact
    • Order information
    • News
    • Manufacturing / Conversion
      • IP-Proofing / Tropicalisation
    • Project Solutions
    • Jobs
  • Ex Protection
    • General Technical Requirements (Ex) EN 60079-0
    • Flameproof (Ex d) – EN 60079-1
    • Pressurisation (Ex p) – EN 60079-2
    • Increased Safety (Ex e) – EN 60079-7
    • Intrinsic Safety (Ex i) – EN 60079-11
    • Non sparking (Ex n) – EN 60079-15
    • Encapsulation (Ex m) – EN 60079-18
  • Products
    • Ex Proof AC Units R32
      • EX Proof AC units
      • Ducted ATEX AC units R32
      • ATEX AC Units R32
    • EX Proof Smart Phones
      • ATEX Zone 1
        • EX Zone 1 iPhone 11
        • EX Zone 1 iPhone 13
      • ATEX Zone 2
        • ATEX Watch S5
        • ATEX Galaxy S10
        • Explosion Proof iPhone 6
        • Explosion Proof iPhone 8
        • ATEX iPhone XS
        • ATEX iPhone XS Max
        • ATEX iPhone XR
        • ATEX iPhone SE-3
        • ATEX iPhone SE
        • ATEX iPhone 11
        • ATEX iPhone 12
        • ATEX iPhone 13
    • Ex Proof Tablets
      • ATEX Zone 1
        • Ex Zone 1 iPad Mini 5
        • Ex Zone 1 iPad Mini 6
      • ATEX Zone 2
        • ATEX iPad Mini 4
        • ATEX iPad Mini 5
        • ATEX iPad Mini 6
        • ATEX iPad 9.7
        • ATEX iPad 10.2
        • ATEX iPad Pro 11
    • ATEX Watch S5
    • ATEX Air Conditioners
    • Explosion Proof ATEX Zone 2 Intrinsically Safe iPad Mini 4
    • ATEX Explosion Proof Panel Heaters
    • ATEX AC Split Systems
    • ATEX / IECEx Cable Glands
      • EX Glands Normal Cable
      • EX Glands Armor Cable
      • EX Locknuts
      • EX Breather
      • EX Drain valve
      • EX Blindplug
    • Climatiseurs antidéflagrants
    • EX Proof VRV Cooling
    • EX Window Air Conditioner
  • EX Proof Smart Phones
    • ATEX Zone 1
      • EX Zone 1 iPhone 11
      • EX Zone 1 iPhone 13
    • ATEX Zone 2
      • ATEX iPhone SE-3
      • ATEX iPhone SE
      • ATEX iPhone 11
      • ATEX iPhone 12
      • ATEX iPhone 13
  • Ex Proof Tablets
    • ATEX Zone 1
      • Ex Zone 1 iPad Mini 5
      • Ex Zone 1 iPad Mini 6
    • ATEX Zone 2
      • ATEX iPad Mini 5
      • ATEX iPad Mini 6
      • ATEX iPad 10.2
      • ATEX iPad Pro 11
  • Downloads
  • Contact
  • Français
    • Anglais
    • Néerlandais
    • Allemand
    • Russe
    • Italien
    • Espagnol
    • Portugais Brésilien
Atexxo / Ex Protection / Non sparking (Ex n) – EN 60079-15

Non sparking (Ex n) – EN 60079-15

This type of protection is suitable for Zone 2 or 22 hazardous areas, and can apply to a large range of equipment.
Generally any electrical device that does not have potentially sparking contacts can be accommodated.

To prevent sparking on PCB’s and other critical electric components, creepage and clearance distances need to be addressed carefully. ATEX coating can be used to reduce risk of arcs and sparks between conductors. In most cases the enclosures need to be dust/water tight to avoid tracking across live circuits.

In addition, specific requirements apply to certain recognised types of equipment, such as motors, luminaires and batteries.
Equipment with potentially sparking contacts such as PCB’s, potentiometers, relays or switches, can be protected in a number of ways:

  • Encapsulation

    Suited to higher power circuits or where creepage and clearance distances on a circuit board are below the required minimum.

  • Sealed

    The sparking device is sealed in an enclosure so that the flammable atmosphere cannot gain access.

  • Restricted breathing

    The enclosure may contain either hot components but no sparking components, or sparking components but with low internal air temperature rise. This method relies on a tight gasket seal on the enclosure joints.

  • Enclosed break

    Applies to small enclosures where the design of the enclosure joints prevents an internal ignition from transmitting to the flammable atmosphere outside. Similar to Ex d but without flame path design requirements.

  • Energy limited (see intrinsic Safety (Ex i) – EN 60079-11)

    Similar to intrinsic safety, the energy available in potentially sparking parts is limited to prevent an ignition occurring. Suitable for circuit designs where detailed knowledge of the design is available and modifications can be accommodated.

Search

    
info@atexxo.com
+31(0)186 601 299
  • Contact
  • Sitemap
  • Anglais
  • Néerlandais
  • Allemand
  • Russe
  • Français
  • Italien
  • Espagnol
  • Portugais Brésilien

© Copyright 2015 atexxo.com · All Rights reserved · Admin